Fret Rocker: 6-sided straight edge for checking unevenness in fret heights before and after levelling.
This improved version has two additional sides - therefore also suitable for smaller instruments such as ukulele and mandolin! Also for long scale basses
It’s a very helpful diagnostic tool to find bumps on all kinds of fret boards. Lay the straight edge so that 3 frets fit under the appropriate side and try to “rock”. If it does, you found a high spot. A very handy tool – should be in every luthiers shop.

• This miniature precision ruler is made of 2mm thick stainless steel
• precision ground on all edges.
• Antiglare sufrace
• Size app.: 100x55mm
• Edge length app.: 12 / 20 / 30 / 50 / 70 / 95mm

Made in GERMANY

This is the professional fret file for smooth and fine (#300) recrowning. Without chatter marks, get faster to results.
The file has two different radius on the edges.
So it files jumbo fret wire on one edge, medium on the other.
Rounded file edges to protect the fret board.
Also for quite flat frets!

• Cutting length: 100mm
• Total length: 200mm

Attention: Thus the industrial diamond coating has very high quality  - it is subject to wear. This file is best used as the fine honing step after using the "coarse" diamond file (04040002) as last step before sanding and buffing. Overheating or cutting very hard materials like stainless steel will reduce the life span very fast.

• Warranty void if been used on stainless steel!

This is the professional coarse (#150) fret file for recrowning as a first step when much material has to be removed in fast strokes.
Use the fine diamond fret file 04040001 as next step to remove possible file marks.
The file has two different radius on the edges.
So it files jumbo fret wire on one edge, medium on the other.
Rounded file edges to protect the fret board.
Also for quite flat frets!

• Cutting length: 100mm
• Total length: 200mm

Attention: Thus the industrial diamond coating has very high quality  - it is subject to wear. Overheating or cutting very hard materials like stainless steel will reduce the life span very fast.

• Warranty void if been used on stainless steel!

Precision straight edge for checking the fret board evenness.
E-Guitar - Acoustic Guitar - Classical Guitar
Further development - measuring range from the saddle to the 24th fret

The notches are placed above the fret positions of the mostly common e-guitar and concert- / western-scales (24 9/16" (624mm)  to 25,6" (650mm)  so the precisely machined edges can reach the wood surface.

• This makes it easy to read and adjust the curvature of the neck very precisely.
• 1. face (short guitar scale): 24 9/16" (624mm) - 25" (635mm)
• 2. face (long guitar scale): 25,2 (640mm) - 25,6" (650mm)
• App. size: 475mm x 40mm x 3mm

MADE IN GERMANY

Precision straight edge for checking and adjusting the fingerboard Flatness (relief) on basses with many scale lengths (30/32/33/34/35/36").
Basses with baritone, short, medium, long and extra length scale can be edited with this straight edge.
The notches are placed so that the frets fit underneath and   so the precisely machined edges can reach the wood surface.
This allows the deflection of the neck to be determined exactly. Depending on the scale, it is possible to check up to 26-28 frets on the fretboard.

• 1. face: Bariton + very short scale 30" (762mm), Short 32" (812,8mm), Medium 33" (838,2mm), Long 34" (863,6mm)
• 2. face: X-Long scale 35" (889mm), XX-Long 36" (914,4mm)
• App. size: 690mm x 40mm x 4mm
• Material: Stainless Steel

MADE IN GERMANY

Fingerboard protector to cover the area next to the fret. Effectively protects for minor repair work on a fret.

Fits all fret wires up to 3mm wide (e.g. bass, guitar).

Protector type: universal

• Slot: 3.0 x 70mm
• Size: 22 x 80mm
• Material: Stainless spring steel

Precisely flat file block for leveling frets. Has hard wood handle which has a flat top.
Can be used with fine grit sand paper for additional honing after filing - a good time saver before recrowning.
Fast material removal and  smooth file cut - low cutting force due to it's propper weight.
Professional Quality.

Precisely flat file block for leveling frets. Has hard wood handle which has a flat top. Can be used with fine grit sand paper for additional honing after filing - a good time saver before recrowning. Very smooth file cut - low cutting force due to it's propper weight. Professional Quality.

Neck support made from hardwood with protective felt. Use e.g. while fretwork.

• Material: hardwood
• Dimensions: approx.25cm x 7.0cm x 3cm

Made in Germany

Fret setting tool for partial knocking down of high spots on fret boards or attach loose fret ends - without having to remove the strings.
The sleek brass chisel fits most fret sizes on guitar and bass. Also suitable for stainless steel.
You position the Fret Setter over the high-spot and knock a little with the plastic side of the fret hammer - checking with the fret rocker.
A very useful tool for quick repairs or for pressing down when gluing.

• Material: brass
• Length: 125mm
• Head width: 10mm
• Min. fret heigth: 0,7mm
• Suitable for all common fretwire sizes

Made in Germany